Glacier White 200 Cup

[Dowling93]

Won't lie, super envious of you getting that for 100 quid, damn you UK folks and the access yee have to better cars and parts for these Clios
If you've the time and are using it as a spare there's no harm in splitting it and doing the synchros

 

[Beany]

I bought a gearbox over the weekend. It was a 197 gearbox for sale for £100.

View attachment 159711

It was described as working when it was removed.

Now I have got the box I am not sure what we are going to do with it apart from take it to bits and see what is inside?

It came with a free driveshaft - but I suspect that it stuck in the box and will need some force to get it out. If a new Gripper wasn't £1,000+ I would be tempted to build this up as a spare box.

Stop messing about and tell us when the sequential is going in

 

[EthanMenace]

Stop messing about and tell us when the sequential is going in

lend us 12 grand then will you, i’ve seen who you do track days with

 

[EthanMenace]

Won't lie, super envious of you getting that for 100 quid, damn you UK folks and the access yee have to better cars and parts for these Clios
If you've the time and are using it as a spare there's no harm in splitting it and doing the synchros

That is hopefully the goal, it’d be nice to learn how to do synchros given how often they seem to go

 

[Beany]

lend us 12 grand then will you, i’ve seen who you do track days with

If I had 12grand spare one would be going in mine

 

[burrellbloke]

We took the Clio to AW Motorworks today to get an alignment done. The gearbox had been dropped out of the car a few times since the last alignment so we knew that the alignment would be slightly out. We also wanted to see if more camber would help with tyre wear on the outside edge of the front wheels.

When we got to AW Motorworks there were quite a few people about who were making various suggestions for a geo set up. I wanted to go a little bit more aggressive generally and was I then enlightened about the importance of caster. Eventually we agreed to go for 4 degrees of negative camber at the front with 5 minutes of toe in for each wheel at the front. At the rear we decided to go just over 2 degrees of negative camber but more toe out with about 15 minutes out on each side.

The idea was that caster is pretty much fixed at about 6 degrees even with a cup racer front end and Gaz Gold top mounts would not give any extra caster. The front of the car was really stable and both @EthanMenace and I were happy with the turn in. After showing a photo of the wear on the last set of tyres we took off the car it was suggested that we had graining on the fronts as the rear of the car was too stable. If we could make the rear more lively with some toe in and higher tyre pressures we could get more rotation in the rear of the car that may help with tyre wear at the front.



This is how the car was set up eventually.



Over a year ago the rear beam was shimmed by Alex and when he did not have a shim that was the right size he cut up a can of Monster and used that as a shim. I am pleased to say that the Monster can shim is still part of the rear beam set up.

Whilst the car was on the ramps it was pointed out that the drivers side rear Gaz damper has a very slight leak so that will need to be rebuilt soon.

We were also given the idea to consider adding another bump stop, or a bigger bump stop to the front Gaz Gold dampers to see if that would stop the front wheels eating in to the front bumper. Another idea we were given was to buy some PMS top mounts as they can give a bit more caster.

Our exhaust is hanging low again and needs to be tightened up so that the elbow near to the rear beam stops twisting and coming down.

We have had front and rear track door cards delivered from Track Car Door Cards but they won't be installed until after we come back from Germany.

We now need to book a track day in early June to test out the new alignment.

On the short term to do list is:

1. Sort out the exhaust
2. Remove and rebuild the rear Gaz dampers
3. Buy and fit a set of PMS top mounts

 

[burrellbloke]

We have just booked on to a MSV track day at Snetterton on Monday 2nd June 2025.

It will be a chance to push the car with the new geo set up to see what it feels like on a track that we are both familiar with.

 

[LiamP]

Jesus, good luck with Coram with that much toe out

Regarding the bump stops I did a lot of work to stop the car hitting the bump stops as it makes the car very tricky to handle under compression. I was getting an oscillating type motion that was causing the car to load/unload the front tyres.

 

[burrellbloke]

Jesus, good luck with Coram with that much toe out

Regarding the bump stops I did a lot of work to stop the car hitting the bump stops as it makes the car very tricky to handle under compression. I was getting an oscillating type motion that was causing the car to load/unload the front tyres.

You are filling me with confidence. If it is awful we can go back to a tamer set up.

 

[LiamP]

You are filling me with confidence. If it is awful we can go back to a tamer set up.

Sorry don’t want to scare you but 15 minutes toe out is very aggressive, I imagine in the racers with Cook at the wheel they probably ran this much but it’s going to be loose especially on the brakes whilst cornering hence mentioning Coram.

The toe in on the front should help things but not sure I know of anyone who has run a setup like this, might be optimal

 

[burrellbloke]

Sorry don’t want to scare you but 15 minutes toe out is very aggressive, I imagine in the racers with Cook at the wheel they probably ran this much but it’s going to be loose especially on the brakes whilst cornering hence mentioning Coram.

The toe in on the front should help things but not sure I know of anyone who has run a setup like this, might be optimal

On track days most of the time we are both in the car, I am not particularly light, so I would expect the car to be carrying an extra 80 to 90 kilos of weight compared to other track cars. It was suggested to us that we had graining on the front tyres on the last set of Direzzas we used because we were over working the front of the car by just dragging the rear of the car around the track. The proposed solution was to make the back end a bit more lively so that the extra rotation would help share the work that the front tyres were doing.

As we all know I am no expert when it comes to cars. I really do value people's opinions, particularly when you (@LiamP ) have raced your Clio and are a current Hot Hatch champion. I am willing to make changes and see if things can be improved. It could all be a disaster but we are trying to cater for two largish men sitting in the car where in the past the back axle has been really stable.

I have absolutely no idea whether our additional weight will impact on the rear toe out.

I think that if the rear axle does get really loose at Snetterton we can throw some spacers on the rear to widen the rear track and give it a bit more stability.